Hardwood Floor Care Will Keep Your Hardwood Looking Fantastic


Hardwood is still the homeowner’s favorite choice of flooring and caring for it takes minimal effort. Unlike laminate or engineered wood, hardwood can be refinished many times, and will add years of warmth and beauty to your home, in addition, to increase its value and speed its resale. Ongoing floor care is Required to keep your hardwood looking its best, however, and there are four major aspects of hardwood floor care:

  1.  Hardwood floor cleaning
  2.  Hardwood floor repair
  3.  Hardwood floor refinishing
  4.  Hardwood floor protection

Clean Your Hardwood Regularly

Understanding how to clean hardwood flooring is vital because the bane of hardwood is dirt and grit, which will scratch and mark the floor if not removed immediately. At the same time, dust is seen more easily on hardwood flooring than it is on linoleum or on carpeting, particularly in the sunlight and especially if the flooring has a dark stain. Hardwood floor care, therefore, means sweeping and dusting often – once a week, at least, and following any function that leaves grit and dirt behind. Regular household cleaning and dusting goods will cause harm, however, and you need to use only products specifically designed for hardwood. Vacuuming is preferable to sweeping because it permits the dirt and dust to be pulled from between the boards, but use a vacuum with a bare floor attachment, not a beater bar, which may damage the timber.

When a more in-depth cleaning is required, use a cleaning method appropriate to the end on the floor. If your floor has a shiny finish, it usually means that polyurethane, or even a water-based urethane, or a similar conclusion has been used to form a protective barrier over the hardwood. If it’s a matte finish, it means that the flooring is protected with a penetrating seal of wax or oil. On neither of these endings is water a suitable cleaning agent, however, both of them can take a surface, damp-mop cleaning, which means the mop isn’t wet but only damp to the touch. You’re cleaning only the surface rather than using enough water to permeate even the oiled-and-waxed hardwood. When using a damp mop on oil and stained hardwood, you may add a little neutral ph hardwood floor cleaner to the water prior to repainting the mop into it. A floor with a protective glossy barrier can accept a generic hardwood floor cleaner supplying it does not contain any wax or acrylic. more info visit on sanjosehardwood.com

The performers are every bit as important as the do’s in hardwood flooring care;

  1.  Don’t use ammonia, routine floor cleaners, household cleaners, or dusting products.
  2.  Never use wax onto a floor using a urethane or alternative glossy finish.
  3.  Never wash hardwood; utilize only a slightly damp mop.

Typically, when your oil and waxed hardwood flooring have suffered surface damage, you need to eliminate the finish with a wax or oil stripper before managing the damage. After finishing the repair, then you re-wax or re-oil the area. Surface damage occurs less often on hardwood shielded by polyurethane or a similar type of sealer, and once it does, the damage is not quite as obvious. When repairing flooring with such finishes, strip the end from the entire board or boards in which the damage has happened. Make your repairs and employ a finishing product to all those boards that is consistent with the rest of the floor.

1. Watermarks: Remove the protective end, rub the marks with fine grade steel wool. Repeat if necessary, clean, and then refinish.

2. Burn marks: Lightly sand the region, use a damp cloth to pick up the grit, and then refinish as wanted.

Refinishing Your Worn Hardwood Floors Will Recapture Their Original Beauty and Value

In a home with shabby hardwood flooring, the greatest improvement you can make would be to refinish the floors. Begin by creating any necessary repairs, and then removing all the furniture and drapes and sealing the vents and registers from the area so you won’t spread dust throughout the house. Sanding flooring is easiest to do with a drum sander and an edging machine for the sides and corners of this space. You can rent these machines, and it is a good idea to lease a buffer or floor polisher in the same time. Plan to make three moves with your sanding gear, using increasingly finer sandpaper every time. Vacuum attentively and pick up every piece of dust and grit with tacking cloths. All dust and dirt has to be removed. You can now apply a stain if you want or you could leave the pure colour and layout of the wood – such as the popular walnut, walnut, or cherry – to be exhibited.

Polish and clean out the dirt and dust from the ground again, then employ your loofah – a polyurethane or a water-based urethane that provides a protective barrier oil and wax, which then permeates the wood and protects from within. Carefully read all of the information accompanying each product, follow the safety advice, and apply as many coats of stain or sealer as suggested by the producer of the merchandise you are using.

As well as regular cleaning, and repairing and refinishing when necessary, there are a number of protective measures you can take to preserve the beauty of your own wood:

1. Use area rugs and mats in high traffic areas and sites of regular spills (e.g., in the front of the stove, sink, and refrigerator). Move these rugs frequently so that these areas of the floor stay exactly the identical color as the exposed floor. At the same time, it is ideal to choose cotton mats as they do not trap water beneath them as rubber or vinyl might.

2. Keep high-heeled shoes in good repair and avoid utilizing stiletto heels.

3. Keep nails trimmed.

4. Clean up spills immediately with a paper towel or dry fabric. A damp cloth may be used for sticky spills, but dry the place immediately afterward with a different towel or cloth.

6. Use sheers or blinds to shield your floors from the discoloration brought on by direct sun rays.